Powerite Pal Underwater and Aquatic Lighting System
PAL Lighting System Underwater Light Aquatic Light Register Online
Powerite PAL Underwater Light
PAL Underwater Lighting PAL for Fibreglass Spa's/Baths PAL for Fibreglass Pools PAL for Concrete Pools PAL Underwater Lighting Order Details

Powerite PAL-2RCS Underwater Light
Page 2 of 2

The unique extraction system featured in the PAL-2RCS allows the light fitting to be removed from the pool with no tools.

For complete order details on the PAL-2RCS and PAL underwater light accessories available, click here.

Installation & Maintenance Instructions on the PAL-2RCS Unique Underwater Light


Installation Instructions for PAL-2RCS Retractable Fitting in Concrete Pool's/Spa's using the PAL-2RCAS

1. Locate the position for mounting the PAL fitting at the centre of one end of the pool or the centre of both ends if required. If the pool is an irregular shape the fitting should be located in a position to obtain the best light spread in the pool. The fitting should be placed 300mm below the water level or 450mm below the top of the pool to enable the retractable part of the fitting to be taken out of the pool if the lamp in the PAL has to be replaced.

2. Fit the PAL-2RCAS concrete wall housing into place in the steel work using wire to secure the housing into position with the mounting lugs around the housing. Ensure the PAL-2RCAS concrete wall housing is Level and Square with the pool wall and there is at least 170mm from the front of the concrete and the back of the housing to ensure the PAL-2RCS light assembly can be glued in correctly when the concrete shell is complete. Glue 20mm conduit adaptor into position and fit the draw wire as shown in Diagram 1 and 2.

Pool 7

3. After the concrete wall is set, trim the pipe down as shown in Diagram 3, then adjust the PAL-2RCS front lens square to the wall with the adjustable lamp assembly. Note: To adjust the angle release the front nut, set the required angle, then lock back up the front nut as shown in Diagram 4.

4. Before the pool finish is applied the PAL-2RCS should be glued into the PAL-2RCAS assembly using PVC glue to seal and locate the fitting into position, as shown in Diagram 5.

Pool 8

5. With the fitting in position in the Concrete Wall the Pool Finish can be applied up to the front face of the fitting as shown on the assembly drawing. Note: The disposable Lens Cover fitted to the PAL-2RCS will protect the fitting while the finish is being applied. The protective lens cover is replaced by the normal lens cover supplied with the PAL-2RCS when the pool is ready to be filled with water.

6. The PAL Transformer is IP64 and can be mounted in the pool zone. Find a suitable position to mount the transformer ensuring it is a minimum of 1.2m above the maximum water level and the transformer must be installed to comply with AS3000.

Pool 9

Lamp Replacement Instructions for Fixed PAL-2RCS Fitting

1. Remove the "Clip-On" Lens Cover on the PAL-2RCS and twist the body in a anti-clockwise direction to retract the fitting from the housing.

2. Unscrew the (6) six lens screws to unclip the lamp from the lamp socket as shown on the Assembly drawing.

3. Replace the Lamp. Note: To ensure reliable operation of your PAL it is essential to use a genuine PAL-2RC Lamp Replacement kit part no. 39-2DL50 or FNV/CG 50 watt Xenon Lamp with UV Cover Glass (No other)
When the lamp is replaced it is recommended to maintain the water tight seal that the "O" ring be also replaced, the "O" ring seal is supplied with the Lamp/Seal replacement kit.

4. When reassembling the PAL-2RCS fitting ensure the "O" ring is sitting correctly and replace the lens, clamping ring and (6) six lens screws and ensure the screws are not overtightened.

5. Feed the wire back into the body and twist the fitting in a clockwise direction to lock into position.

Pool 14